How To Fix A Camera That Won’t Turn On? (A Step By Step Guide)

Camera problems are common and are often tricky to fix as it can be hard to know where to start. If you’re looking for a way to fix a camera that won’t turn on, this blog post can help you.
Here, we will discuss the usual issues with cameras that won’t turn on. You know that there is no one-size-fits-all solution, but it will help you identify the problem and fix it correctly. So, let’s get started.

Troubleshoot and Fix Your Camera that won’t Turn On

Before you start troubleshooting, it is crucial to have an idea of what the problem might be. This will help you find the right tools and parts to fix it. Moreover, finding out the fault on your own will boost your confidence that can help you fix the camera. So, let’s get started.

Check If Your Camera’s Battery is Dead 

If your camera doesn’t turn on, the first thing that you should do is remove the battery from the camera and then reinsert it into the compartment. After this, try turning the camera on again.

If removing the battery and reinserting it still doesn’t work, there may be a power stroke in the camera. This means that the battery has run out of charge, and the camera has stopped working altogether.

It can happen in digital cameras that use a lot of power or in older film cameras where the batteries are less efficient. In this case, recharge the battery and switch on the camera.

If this doesn’t work either, then there is a good chance that the battery is dead. A dead battery usually means there’s a problem with the battery. To fix this, you’ll need to find out what’s wrong with your battery.

Recharge the battery first and check it with a multimeter (if available). You can find instructions online if you don’t know how to do this. If there is no charge on the battery, it is likely faulty and needs replacing.

Check If Your Camera is Overheating

Many internal components of a digital camera operate at very high temperatures, so they must be kept cool to function correctly. If your camera gets too hot, it might not function correctly or at all.

This can be caused by several factors, including extended exposure to direct sunlight. Also, it may happen because of poor ventilation (such as a car on a hot day) or leaving your camera in a hot vehicle while it gets cold outside.

In this case, the first thing that you should do is stop using it for a while. Then, go outside or somewhere cool and remove the battery. After this, leave it in a cool place for about 15 minutes and then turn it on again.

Check If Your Camera has been Exposed to Water

Water can cause problems with cameras and electronics in general, above all if it gets into sensitive areas where it can damage components. This can happen when taking pictures in a pool, the ocean, or other water-related location.

In this case, remove the battery and wait for it to dry before inserting it again. If there is still no power, clean it with a brush or cloth (preferably one that is soft and non-abrasive).

Also, look for any wet spots on the camera or lens, especially around the lens mount area and controls (where the cable connects). If there are any, wipe them dry using a paper towel or a microfiber cloth.

Also, make sure that your camera does not have any cracks or holes in it.

Check If Your Camera is Still Under Warranty

If your camera is still under warranty, contact your manufacturer for assistance. You can use their website or call their customer care number and claim the warranty.

If your manufacturer does not offer warranty service, you can try contacting other repair shops that may have access to parts compatible with your model. But before going to a third party, you should try to fix it yourself first.

The following two steps are for you if your camera isn’t under warranty.

Check If the Power Switch is Faulty

The power switch is a small metal lever usually attached to the camera by a small screw. This switch turns on the power to the camera. That’s why you need to check it. If it’s stuck or broken, then you’ll need to fix it before you can use your camera again.

Usually, the power switch is located on the bottom or side of a camera. However, it can vary depending on the type of camera.

You may need to take off your battery cover to access the power switch in some cases. You can also check the manual for your camera for instructions on doing this.

If the power switch looks damaged, then you’ll need to replace it. If you’re unsure how to do this, take it to a professional service center.

Check If the Circuit Board is Faulty

If none of these steps helped, you might have a faulty circuit board within your camera. The circuit board connects all of the different parts within your digital or film camera and allows them to work correctly.

This can be difficult to fix if it’s something simple like a loose connection between two wires or something more complicated like an integrated circuit (or IC) failing. In such cases, you’ll need to replace the board with a new one (you can refer to your owner’s manual for instructions).

However, this isn’t something that most people should try doing themselves unless they’re very confident in their abilities and have experience in electronics repair work before. Instead, go to a professional service center, and they will take care of the problem.

If none of the above steps worked, then it’s likely that your camera has a serious fault. It may not be worth fixing, especially if the repair cost would cost more than the value of your camera. In this case, it may be better to buy a new camera.

Conclusion

Hopefully, this article was helpful for you, and by now, you’ve got a brief idea of how to fix a camera that won’t turn on. Please feel free to contact us by commenting below or sending an email if you need any further assistance.

If you want to learn more about your camera, you should read the user manual that came with the camera. Moreover, you can check out your manufacturer’s website (if they have one) for more information.